ELPLP50 V13H010L50 Replacement Projector Lamp Compatible with Epson EB-824 EB-825 EB-826W EB-84e EB-84he EB-85 EMP-825 EMP-84 EMP-84he H294B H295A H296A H297A H353A H353B H353C H354C H355B H356C H357C
ELPLP50 V13H010L50 Replacement Projector Lamp Compatible with Epson EB-824 EB-825 EB-826W EB-84e EB-84he EB-85 EMP-825 EMP-84 EMP-84he H294B H295A H296A H297A H353A H353B H353C H354C H355B H356C H357C
Projector Lamp Type: Projector lamp with Housing Model number: V13H010L50 Projector lamp Compatible with Projector models: Epson EB-824 EB-824H EB-825 EB-825H EB-826W EB-826WH EB-84 EB-84e EB-84H EB-84he EB-84l EB-85 EB-85H EB-D290 EMP-825 EMP-84 EMP-84he H294B H295A H295B H296A H297A H297B H353A H353B H353C H354C H355B H355C H356C H357C H370C PowerLite 825 PowerLite 825+ PowerLite 826W PowerLite 826W+ PowerLite 84 PowerLite 84+ PowerLite 85 PowerLite 85+ Bare lamp is available for sell Read more Step 1. Unplug the power cord from your projector and let the lamp cool down. Step 2. Locate the lamp access panel on your projector and remove the screws and access panel. Step 3. Remove any screws holding the lamp housing into the projector. Step 4. Reach in and firmly pull the lamp housing out of the projector. Step 5. Place the new lamp housing into the projector in the same orientation as you removed the old lamp. Step 6. Wiggle the lamp into place and make sure full contact is made inside of the projector. Step 7. Replace the lamp mounting screws to secure the lamp into the projector. Step 8. Replace the lamp access panel and secure the screws. Step 9. Plug in your projector and power it on. Step 10. Reset the lamp counter. Some lamps will reset the lamp counter automatically when a new lamp is placed in. Read more Where is My Projector Lamp Located A projector lamp can be found by locating a square or rectangular plastic plate somewhere on the outside of the projector; the plate is usually on the bottom of the projector, but can sometimes be found on the top or sides. This cover is usually secured by two screws; undo these screws and lift the plate off to reveal the bottom of the plastic housing (the module) that holds the projector lamp in place in your projector. This plastic housing usually has a handle attached to it. Pull gently on this handle to remove the projector lamp from your projector. It is time to replace the lamp when: Picture has become dull and lacks brightness. There is an obvious decline in picture clarity and sharpness. Your lamp is flickering. There is difficulty or a delay when turning the machine on. A light comes on that warns you that it may be time to change your lamp. Note: 1. Let the lamp cool down before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 2. Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 3. Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on. Read more
Product Features
- Compatible with Epson H294B H295A H296A H297A H353A H353B H353C H354C H355B H355C H356C
- Projector Lamp with Housng
- All lamps are produced by our own factory
- All lamps are tested at our factory before leaving the facility
- Cheaper Bare Lamp without Housing Also Available for Sale