Stemedu ESP32-S3 ESP32-S3-DevKitC-1 N8R8 Development Board based on ESP32-S3-WROOM-1 module, 8 MB Quad flash and 8 MB Octal PSRAM, SPI Interface WiFi +Bluetooth 2 in 1 Microcontroller for Ar-duino IDE
Stemedu ESP32-S3 ESP32-S3-DevKitC-1 N8R8 Development Board based on ESP32-S3-WROOM-1 module, 8 MB Quad flash and 8 MB Octal PSRAM, SPI Interface WiFi +Bluetooth 2 in 1 Microcontroller for Ar-duino IDE
Description
ESP32-S3-DevKitC-1-N8R8 ESP32-S3-WROOM-1 8MB Flash 8MB PSRAM Description: The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, a general-purpose Wi-Fi + Bluetooth LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. This version is equipped with the ESP32-S3-WROOM-1 (PCB antenna) with 8MB Flash and 8 MB PSRAM. Please note: The S3 is similar to the ESP32-S2 - but adds a dual core and Bluetooth LE (not classic!) However, there is minimal support for this dev board. For example, as of the time of this writing, there is no Arduino or CircuitPython support - only ESP IDF! Please purchase if you're doing development with the S3, and OK with stuff not working 100% out of the box. Read more There are three mutually exclusive ways to provide power to the board: USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended)5V and G (GND) pins3v3 and G (GND) pins Applications: Generic Low-power IoT Sensor Hub Generic Low-power IoT Data Loggers Cameras for Video StreamingOver-the-top (OTT) DevicesUSB DevicesSpeech RecognitionImage RecognitionMesh NetworkHome AutomationSmart BuildingIndustrial AutomationSmart AgricultureAudio ApplicationsHealth Care ApplicationsWi-Fi-enabled ToysWearable ElectronicsRetail & Catering Applications Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard. We particularly like that there's a debug UART/USB port and a separate native USB port, so you can upload/debug/USB all at once. Components: ESP32-S3-WROOM-1: ESP32-S3-WROOM-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module that has a rich set of peripherals. It provides acceleration for neural network computing and signal processing workloads. ESP32-S3-WROOM-1 comes with a PCB antenna.5V to 3.3V LDO: Power regulator that converts a 5V supply into a 3.3V output.Pin Headers: All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming.USB-to-UART Port: A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB-to-UART bridge.Native ESP32-S3 USB Port: ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 specification. The interface is used for power supply to the board, for flashing applications to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging.Boot Button: Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.Reset ButtonUSB-to-UART Bridge: Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.RGB LED: Addressable RGB LED, driven by GPIO48.3.3V Power On LED: Turns on when the USB power is connected to the board. Please Click Here Please Click Here Please Click Here Please Click Here Please Click Here Please Click Here Product Stemedu ESP32-PICO-KIT V4.1 ESP32 Development Board WiFi + Bluetooth Dual-Mode Microcontroller Module Integrated with 40 MHz 4 MB flash RF Filter Capacitors for Ar duino Stemedu ESP-01S USB to ESP8266 ESP-01S Wireless WiFi Adapter Module Wi-Fi CH340G 4.5-5.5V, 115200 Baud Rate, Upgrade to 4MB Flash Stemedu 2PCS ESP8266 NodeMCU Devkit CP2102 ESP-12E Development Board IIC SPI Interface Open Source IoT Module WiFi 2.4G Flash 4MB Serial Module for Ar-duino Stemedu ESP8266 ESP-01S Adapter WiFi Module Wireless Serial Transceiver with 4MB Flash DIP-8 3-6V for Arduino (Pack of 5PCS) Stemedu ESP32-C3-DevKitC-02 Core Development Board ESP32-C3-WROOM-02 Module with 4MB SPI Flash, WiFi and Bluetooth 2-in-1 Microcontroller Processor for Ar-duino IDE Stemedu 32Pin ESP32 ESP32-WROOM-32 Development Board ESP-32S WiFi + Bluetooth Dual Cores Microcontroller Processor for Micropython Expressif (2PCS) Package 1 PC 1 Set 2 PCS 5 PCS 1 PC 2 PCS Module / ESP32-C3-WROOM-02 ESP32-WROOM-32 WiFi ✓ ✓ ✓ ✓ ✓ ✓ Bluetooth ✓ ✓ ✓ Flash 4MB 4MB 4MB 4MB 4MB USB interface Micro USB Micro USB Micro USB Micro USB DC0-25V Voltage Detection Module Tester LM393 Sound Sensor Microphone Module ESP8266 ESP-01S Breakout Board 5PCS GY-521 MPU-6050 Accelerometer Gyro Sensor LM317 DC-DC Converter Step Down Module MAX7219 8-Digital 7-Segment Display Module Model LM393 GY-521 MPU-6050 LM317 MAX7219 Qty 5 Packs 5 Packs 10 Packs 5 Packs 5 Packs 5 Packs
Features:
- ESP32-S3 Development Kits offer the ESP32-S3-DevKitC-1 entry-level development board equipped with either ESP32-S3-WROOM- 1 or ESP32-S3-WROOM-1U, a general-purpose Wi-Fi + BLUETOOTH LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. This version is equipped with the ESP32-S3-WROOM-1 (PCB antenna) with 8MB Flash and 8 MB PSRAM.
- Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard.
- ESP32-S3 has 45 programmable GPIOs and common peripheral interfaces such as SPI, I2S, I2C, PWM, RMT, ADC, UART, SD/MMC host controller and TWAITM controller.
- Tutorial link: https(:)//docs.espressif(Dot)com/projects/esp-idf/en/latest/esp32s3/hw-reference/esp32s3/user-guide-devkitc-1(Dot)html
- If any question, how to contact us? Please click Stemedu(you can find "Sold by Stemedu" under Buy Now button), in the new page, click Ask a question to email us