Fittings for Aluminum Track-Multi Packs

{"id":5477900157083,"title":"Aluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack 4 Pack","handle":"aluminum-track-fitting-4-000-lb-capacity-w-aluminum-keeper-tiedowns-4-pack-4-pack","description":"\u003ch3\u003eAluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eSize:4 Pack Single Stud w\/ Stainless Steel \"O\" ring - 4,000 lb. capacity\nrating. This fitting fits all aluminum tracking similar to the track in the\nimage above. Single stud refers to the number of \"fingers\" that it captures\nwhen attached. The fittings' aluminum base will not rust. It is SPRING LOADED\nto permit simple attach and detach operation. To detach, simply pull up on the\nspring loaded mechanism and then slide forward or back and the fitting\nreleases. To attach, rest the fitting in the load track, then push down on the\nbase and push forward. The single stud fitting attaches to one set of\n\"fingers\" in the load track. For a stronger and more secure fitting consider\ntriple or double stud fitting. IT IS NOT recommended to pull at an angle\ngreater than 45 degrees. As a rule of thumb you lose about half your rating at\na 45 degree angle. RATED CAPACITY: Also known as assembly capacity or break\nstrength is the minimum load a complete assembly can withstand before failure\nin a laboratory pull test when the product is new. WLL The maximum load weight\na tie-down should be subjected to during normal use. To assist in making the\nproper tie-down choice the Federal D.O.T. requires the W.L.L. to be 1\/3 of the\nRated Capacity.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eThis listing is for four (4) single stud fittings with a RATED CAPACITY* of 4,000 lbs. The W.L.L.** (working load limit) is a 2,166 lb. capacity. This fitting fits all aluminum track that is similar to the track shown in the secondary image above. We refer to the track as aluminum load track. It is also commonly referred to as airplane track, seat or simply S track.\u003c\/li\u003e\n \u003cli\u003e*RATED CAPACITY: Also known as assembly capacity or break strength is the minimum load a complete assembly can withstand before failure in a laboratory pull test when the product is new. **W.L.L. The maximum load weight a tie-down should be subjected to during normal use. To assist in making the proper tie-down choice the Federal D.O.T. requires the W.L.L. to be 1\/3 of the Rated Capacity.\u003c\/li\u003e\n \u003cli\u003eThe fitting is SPRING LOADED to permit simple attach and detach operation. To detach, simply pull up on the spring loaded mechanism and then slide forward or back and the fitting releases. To attach, rest the fitting in the load track, then push down on the base and push forward.\u003c\/li\u003e\n \u003cli\u003eSingle stud refers to the number of \"fingers\" that it captures when attached to the aluminum track. The base measures 1-3\/8\" long x 3\/4\" wide with a 3\/16\" diameter stainless steel ring that measures 1-3\/8\" on center.\u003c\/li\u003e\n \u003cli\u003eThe fittings' aluminum base and stainless steel ring will not rust. The steel stud\/center post is zinc plated to inhibit corrosion.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n\n\n\n","published_at":"2020-08-10T01:27:33+10:00","created_at":"2020-08-10T01:27:33+10:00","vendor":"Fittings for Aluminum Track-Multi Packs","type":"Ratcheting","tags":[],"price":16200,"price_min":16200,"price_max":16200,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":35413828534427,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B006NFH2IO","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"Aluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack 4 Pack","public_title":null,"options":["Default Title"],"price":16200,"weight":243,"compare_at_price":null,"inventory_management":null,"barcode":"736211307484","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/leoforward.com\/cdn\/shop\/products\/B006NFH2IO.jpg?v=1651036493","\/\/leoforward.com\/cdn\/shop\/products\/61DGgUIbWTL.jpg?v=1622849122","\/\/leoforward.com\/cdn\/shop\/products\/516OtUvrMUL.jpg?v=1622849122","\/\/leoforward.com\/cdn\/shop\/products\/71FXYtjZ29L.jpg?v=1622849122"],"featured_image":"\/\/leoforward.com\/cdn\/shop\/products\/B006NFH2IO.jpg?v=1651036493","options":["Title"],"media":[{"alt":" [AUSTRALIA] - Aluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack 4 Pack","id":29643027480813,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"\/\/leoforward.com\/cdn\/shop\/products\/B006NFH2IO.jpg?v=1651036493"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"\/\/leoforward.com\/cdn\/shop\/products\/B006NFH2IO.jpg?v=1651036493","width":1500},{"alt":" [AUSTRALIA] - Aluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack 4 Pack","id":10574709588123,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/leoforward.com\/cdn\/shop\/products\/61DGgUIbWTL.jpg?v=1622849122"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/leoforward.com\/cdn\/shop\/products\/61DGgUIbWTL.jpg?v=1622849122","width":1000},{"alt":" [AUSTRALIA] - Aluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack 4 Pack","id":10574709620891,"position":3,"preview_image":{"aspect_ratio":1.499,"height":667,"width":1000,"src":"\/\/leoforward.com\/cdn\/shop\/products\/516OtUvrMUL.jpg?v=1622849122"},"aspect_ratio":1.499,"height":667,"media_type":"image","src":"\/\/leoforward.com\/cdn\/shop\/products\/516OtUvrMUL.jpg?v=1622849122","width":1000},{"alt":" [AUSTRALIA] - Aluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack 4 Pack","id":10574709653659,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1500,"width":1500,"src":"\/\/leoforward.com\/cdn\/shop\/products\/71FXYtjZ29L.jpg?v=1622849122"},"aspect_ratio":1.0,"height":1500,"media_type":"image","src":"\/\/leoforward.com\/cdn\/shop\/products\/71FXYtjZ29L.jpg?v=1622849122","width":1500}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003ch3\u003eAluminum Track Fitting 4,000 lb Capacity w\/Aluminum Keeper, Tiedowns 4-Pack\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eSize:4 Pack Single Stud w\/ Stainless Steel \"O\" ring - 4,000 lb. capacity\nrating. This fitting fits all aluminum tracking similar to the track in the\nimage above. Single stud refers to the number of \"fingers\" that it captures\nwhen attached. The fittings' aluminum base will not rust. It is SPRING LOADED\nto permit simple attach and detach operation. To detach, simply pull up on the\nspring loaded mechanism and then slide forward or back and the fitting\nreleases. To attach, rest the fitting in the load track, then push down on the\nbase and push forward. The single stud fitting attaches to one set of\n\"fingers\" in the load track. For a stronger and more secure fitting consider\ntriple or double stud fitting. IT IS NOT recommended to pull at an angle\ngreater than 45 degrees. As a rule of thumb you lose about half your rating at\na 45 degree angle. RATED CAPACITY: Also known as assembly capacity or break\nstrength is the minimum load a complete assembly can withstand before failure\nin a laboratory pull test when the product is new. WLL The maximum load weight\na tie-down should be subjected to during normal use. To assist in making the\nproper tie-down choice the Federal D.O.T. requires the W.L.L. to be 1\/3 of the\nRated Capacity.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eThis listing is for four (4) single stud fittings with a RATED CAPACITY* of 4,000 lbs. The W.L.L.** (working load limit) is a 2,166 lb. capacity. This fitting fits all aluminum track that is similar to the track shown in the secondary image above. We refer to the track as aluminum load track. It is also commonly referred to as airplane track, seat or simply S track.\u003c\/li\u003e\n \u003cli\u003e*RATED CAPACITY: Also known as assembly capacity or break strength is the minimum load a complete assembly can withstand before failure in a laboratory pull test when the product is new. **W.L.L. The maximum load weight a tie-down should be subjected to during normal use. To assist in making the proper tie-down choice the Federal D.O.T. requires the W.L.L. to be 1\/3 of the Rated Capacity.\u003c\/li\u003e\n \u003cli\u003eThe fitting is SPRING LOADED to permit simple attach and detach operation. To detach, simply pull up on the spring loaded mechanism and then slide forward or back and the fitting releases. To attach, rest the fitting in the load track, then push down on the base and push forward.\u003c\/li\u003e\n \u003cli\u003eSingle stud refers to the number of \"fingers\" that it captures when attached to the aluminum track. The base measures 1-3\/8\" long x 3\/4\" wide with a 3\/16\" diameter stainless steel ring that measures 1-3\/8\" on center.\u003c\/li\u003e\n \u003cli\u003eThe fittings' aluminum base and stainless steel ring will not rust. The steel stud\/center post is zinc plated to inhibit corrosion.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n\n\n\n"}